The Ultimate Cargo Solution: A Professional Installation Guide for the STREK OFF ROAD INEOS Grenadier 2026 Rear Trunk Drawer System
The INEOS Grenadier is engineered for adventure, but even the most capable off-roader benefits from superior organization. The STREK OFF ROAD Rear Trunk Drawer System is a purpose-built upgrade designed to transform your cargo area from a chaotic space into a highly efficient, secure storage hub.
This guide breaks down the installation process into clear, professional stages. By following these steps precisely, you will ensure a robust, factory-quality fit for your new drawer system.
Watch the complete installation video:
Pre-Installation Checklist: Preparation is Paramount
Before you even unbox the main components, a thorough preparation phase is essential for a smooth installation process.
- Accessory Verification: Immediately verify that all product accessories listed in your kit manifest are present and accounted for.
- Tool Readiness: Gather all necessary installation tools. While the exact tools can vary by kit revision, general requirements often include basic hand tools and potentially a drill/impact driver.
- Clear the Workspace: Folding down the second-row seat is a critical preparatory step. This action creates the necessary clearance, making it significantly easier to maneuver and secure the main frame within the trunk area.
Phase 1: Main Frame Assembly and Structural Integrity
This phase focuses on establishing the core structure of the drawer system within the vehicle. Precision in alignment is key here.
Securing the Side Panels and Baffle Plate
- Main Frame Placement: Carefully place the main frame into the trunk space.
- Initial Panel Insertion: Insert the right side panel into its designated slot on the main frame.
-
Baffle Plate Connection (Right Side):
- Alignment: Align the mounting holes of the baffle plate with those of the main frame. Pay close attention to the visual indicators—the mounting holes are specifically indicated by the red circles in the guide visuals.
- Fastening: The baffle plate is connected to the main frame with screws.
- Sealing Check: After connection, the position of the baffle plate should be in contact with the sealing strip of the outer ring. This ensures a tight fit against the vehicle body.
- Left Side Repetition: Insert the left side panel. Repeat the baffle plate connection process: align holes, secure with screws, and confirm contact with the outer ring sealing strip.
Phase 2: Anchoring the Frame to the Vehicle Floor
The stability of the entire system relies on how securely the main frame is anchored to the vehicle's floor structure. This involves utilizing the factory mounting points via positioning blocks.
Bottom Frame Securing Protocol
Crucial Note: The bottom of the main frame must be secured using four positioning blocks, four screws, and four washers.
-
Support Bracket Installation:
- Insert the left middle support bracket and secure it to the main frame with screws.
- Insert the left rear support bracket and connect it to the main frame with screws.
- Similarly, insert the right middle and right rear support brackets and connect them to the main frame.
-
Floor Anchoring Procedure:
- Positioning Block Placement: Place the positioning block into the trunk rail, ensuring it is precisely positioned at the intersection of the main frame crossbar and the rail. This ensures the load is transferred correctly.
- Screw Assembly: Insert the washer onto the screw, then insert the screw into the threaded hole of the positioning block, and secure it.
- Completing the Base: Repeat this process for the other three positions to fully anchor the base of the main frame.
Phase 3: Top Panel Installation and Final Drawer Insertion
With the base and side structure firmly secured, the final steps involve installing the top surface and completing the drawer mechanism.
Finalizing the Top Structure
- Top Panel Installation: Install the left top panel, carefully aligning the holes in the top panel with the mounting holes in the frame.
- Top Panel Fastening: Install the top panel retaining clips and the screws that secure the top panel to the frame in sequence.
- Side Panel Completion: Install the left and right side panels at the top in sequence.
Drawer Integration
- Final Hardware: After installing the remaining latch screws and top panel connecting screws, the structure is ready for the moving components.
- Drawer Insertion: Gently insert the drawer into the main frame. Ensure the slides engage correctly and the drawer moves smoothly through its full range of motion.
Conclusion: Mission Accomplished – Optimized for the Trail
The installation of the STREK OFF ROAD Drawer System is a multi-stage process that demands attention to detail, particularly concerning the alignment of the baffle plate and the four-point floor anchoring. By meticulously following these steps—from clearing the second row to securing the final top panel screws—you have successfully integrated a professional-grade storage solution into your INEOS Grenadier.
This system not only maximizes your cargo capacity but also keeps your essential gear organized and accessible, whether you are setting up camp or navigating challenging terrain. Enjoy the enhanced utility and rugged organization this premium system brings to your overland adventures!